Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
This great article down below on the subject of Tools You Need to Install a New Bathtub is relatively interesting. Check it out yourself and figure out what you think of it.
Installing a tub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the project can relocate speedily; if you have to open up a wall surface to remove the old tub and also position the new bathtub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have certified on your own for the task and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to consider using one before you start. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly aid you install a new bathtub in your restroom if you have actually currently gotten a brand-new bathtub and also do not need to change the arrangement of your previous water system pipelines.
Your devices and also material list need to consist of the following:
Planning for the Setup
To start with, the supporting structure provided with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to stop pressure on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, put the tub in the required placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub up until the level reads level.
To mount taps, fit all-time low of the outermost adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the water and check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub and additionally examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been used a minimum of once as this will certainly settle it into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Safeguard the tap in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous type must be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with wetness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can fracture rather early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that review on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when scouting around the internet. Make sure you take a moment to promote this content if you enjoyed reading it. Kudos for your time. Visit us again soon.
Excellence awaits, dial! Report this page